Brainy Quote of the Day

Showing posts with label Solid State Physics. Show all posts
Showing posts with label Solid State Physics. Show all posts

Wednesday, September 6, 2017

Quantum Light on a Chip...

A laser (green) excites the quantum dot (red) in this diagram of the chip. The ring, which is tuned via applying voltage to the yellow contacts, manipulates the characteristics of individual photons (ellipsoids).
Topics: Laser, Nanotechnology, Photonics, Quantum Dots, Quantum Mechanics, Solid State Physics

Ideally, optical circuits would generate and shuttle light so well that researchers could use them to transmit encoded information, sense chemical species, and perform quantum computations. But because the components for each circuit—light sources, mirrors, splitters, filters, and waveguides—occupy several feet of table space, they cannot manipulate light down to the nanoscale. In an effort to downsize components and produce practical quantum photonic devices, researchers have been tinkering with nonlinear materials, atomic defects, and traditional semiconductors at the nanoscale.

Now Ali Elshaari at KTH Stockholm and his colleagues have taken a major stride by embedding circuit components on a CMOS-compatible chip that takes up a millionth the area of a tabletop apparatus. The key innovation was implementing precise control over quantum dot light sources, which emit photons in specific quantum states, including entangled ones, when excited by lasers. Scientists had struggled to control the dots’ emission and integrate the dots with waveguides for on-chip applications. Elshaari’s team devised a special geometry that optimized the alignment of the dots’ light emission with the fundamental waveguide mode, which resulted in high coupling efficiencies. To control the emission, an electrically tunable device acted as a spectral filter that could fine-tune the photon characteristics.

Manipulating quantum light on a chip, Katyayani Seal, Physics Today

Wednesday, August 30, 2017

Flexible Crystal...

Credit: University of Queensland
Topics: Consumer Electronics, Materials Science, Solid State Physics, Quasicrystal

Queensland researchers have shown that single crystals, typically thought of as brittle and inelastic, are flexible enough to be bent repeatedly and even tied in a knot.

Researchers from Queensland University of Technology (QUT) and The University of Queensland (UQ) determined and measured the structural mechanism behind the elasticity of the crystals down to the atomic level.

Their work, published in Nature Chemistry, opens the door for the use of flexible crystals in applications in industry and technology.

The research was led by ARC Future Fellows Associate Professor Jack Clegg in UQ's School of Chemistry and Molecular Biosciences and Associate Professor John McMurtrie in QUT's Science and Engineering Faculty.

Associate Professor McMurtrie said the results challenged conventional thinking about crystalline structures.

"Crystals are something we work with a lot – they're typically grown in small blocks, are hard and brittle, and when struck or bent they crack or shatter," he said.

"While it has previously been observed that some crystals could bend, this is the first study to examine the process in detail.

"We found that the crystals exhibit traditional characteristics of not only hard matter, but soft matter like nylon."

Bendable crystals tie current thinking in knots, Phys.org

Tuesday, August 22, 2017

E-Fields, Nuclear Spin, Qubits, Silicon...

Photograph of a sapphire wafer that is patterned with the photonic bandgap resonators used in this work. It shows two full devices and parts of four others. Before using them in experiments they are cut out of the array and wired up. The devices themselves are about 1 cm long. The serpentine structures are microwave Bragg mirrors and the straight lines of varying width at the center of each device are the microwave cavities. Courtesy: A Sigillito

Topics: Electromagnetism, Solid State Physics, Quantum Dots, Quantum Mechanics

Researchers at Princeton University and the Lawrence Berkeley National Laboratory have succeeded in controlling nuclear spins in silicon by purely electrical means. Until now, electronic or nuclear spins could only be manipulated through radio-frequency magnetic fields. The feat could help in the development of quantum processors based on nuclear spin qubits.

Classical computers store and process information as "bits" that can have one of two logic states ("0" or "1"), but quantum computers work on the principle that a quantum particle (such as an electron or atomic nucleus) can be in two states at the same time – "spin up" or "spin down". These two spin states represent a logical "1") or a "0", so N such particles –or quantum bits (qubits) – could be combined or "entangled" to represent 2N values simultaneously. This would lead to the parallel processing of information on a massive scale not possible with conventional computers.

In practice, it is difficult to make even the simplest quantum computer, however, because these quantum states are fragile and are easily destroyed. They are also difficult to control. For a qubit to work, it should thus be well isolated from its environment to preserve its quantum properties, and prevent "decoherence". At the same time it should be robust enough so that its state can be read out and manipulated. The intrinsic magnetic moment of an atomic core, or nuclear spin, is a good qubit candidate in this respect because it fulfills all of these criteria.

There is a problem, however, in that the magnetic moment of a nuclear spin is 10 billion times smaller than the moment of one bit of a modern hard drive, and it is almost impossible to detect, let alone manipulate, such a tiny signal.

Electric fields control nuclear spin qubits in silicon, Belle Dumé, Nanotechweb.org

Tuesday, August 8, 2017

B-Doped Q-Carbon Superconductors...

FIG. 1.
SIMS profiles of (a) as-deposited boron and carbon layers with the inset showing a schematic of the alternating layers of amorphous carbon and boron deposited on c-sapphire using the pulsed laser deposition technique and (b) pulsed laser annealed (B-doped Q-carbon) thin films with the inset showing a schematic of B-doped amorphous Q-carbon formed on c-sapphire.

Topics: Condensed Matter Physics, Materials Science, Solid State Physics, Superconductors

ABSTRACT
Following a brief report on high-temperature superconductivity in B-doped Q-carbon [Bhaumik et al., ACS Nano 11(6), 5351–5357 (2017)], we present detailed structure-property correlations to understand the origin of superconductivity in strongly bonded lightweight materials and methods to further enhance the superconducting transition temperature (Tc). Nanosecond melting of carbon in a super undercooled state and rapid quenching result in a strongly bonded unique phase of B-doped Q-carbon. The temperature-dependent resistivity and magnetic susceptibility measurements demonstrate type II superconductivity in this material with a transition temperature of 36.0 ± 0.5 K and an upper critical field of 5.4 T at ∼0 K. It has also been shown that in B-doped Q-carbon, the upper critical magnetic field (Hc2(T)) follows Hc2(0) [1-(T/Tc)2.1] temperature dependence and is consistent with the Bardeen–Cooper–Schrieffer formalism. In the present study, B-doped Q-carbon thin films are formed on sapphire substrates by employing pulsed laser annealing (PLA) using a nanosecond excimer laser. This process involves the rapid quenching of highly undercooled melt of homogenously mixed B and C. Through the structure-property correlation measurements in B-doped Q-carbon, we estimate a higher electronic density of states near the Fermi level. Higher density of states near the Fermi-level along with higher Debye temperature and phonon frequency are responsible for the enhanced Tc. As a result of rapid melting and quenching, we can achieve 17.0 ± 1.0 or higher atomic % of B in the electrically active sites of Q-carbon which leads to the formation of shallow electronic states near the valence band maximum. From the critical current density versus field moments, the value of critical current density (Jc (2T)) in B-doped Q-carbon at 21 K is calculated as 4.3 × 107 A cm−2, which indicates that this novel material can be used for the persistent mode of operation in MRI and nuclear magnetic resonance applications. This discovery of high-temperature superconductivity in B-doped amorphous Q-carbon shows that the non-equilibrium synthesis technique using the super undercooling process can be used to fabricate materials with greatly enhanced physical properties.

A novel high-temperature carbon-based superconductor: B-doped Q-carbon
Anagh Bhaumik1, Ritesh Sachan1,2, and Jagdish Narayan1,a)
Journal of Applied Physics 122, 045301 (2017); doi: http://dx.doi.org/10.1063/1.4994787

Friday, July 7, 2017

Selenide Vibrations...

In this illustration, an infrared laser beam (orange) triggers atomic vibrations in a thin layer of iron selenide, which are then recorded by ultrafast X-ray laser pulses (white) to create an ultrafast movie. The motion of the selenium atoms (red) changes the energy of the electron orbitals of the iron atoms (blue). (Courtesy: Greg Stewart/SLAC National Accelerator Laboratory)

Topics: Condensed Matter Physics, Materials Science, Solid State Physics, Superconductors

Two important breakthroughs in the understanding of iron-selenide superconductors have been made by two independent research groups. One team has shown that the electrons responsible for superconductivity in the material probably come from a specific atomic orbital. The other team, meanwhile, has measured the interaction between electrons and atomic vibrations in iron selenide, which is believed to be involved in its superconductivity.

The research could shed light on the mystery of why some materials based on iron selenide are superconductors at relatively high temperatures, which has puzzled physicists for more than a decade. While bulk iron selenide is a superconductor below 8.5K, this transition temperature can reach as high as 75K when an ultrathin trilayer of the material is grown on certain substrates.

Experiments shed new light on iron superconductors, Hamish Johnston, Physics World

Friday, May 26, 2017

Ultra Cold and Fermi-Hubbard...

Raw fermionic microscope image (left) and processed image showing that spin-up atoms occupy alternating lattice sites as expected in an antiferromagnet. The spin-down atoms have been removed from the image. (Courtesy: A Mazurenko et al. / Nature)

Topics: Condensed Matter Physics, Optical Physics, Quantum Mechanics, Solid State Physics, Superconductors

New insights into a popular and potentially useful model of how electrons behave in solids have been provided by an experiment involving ultracold atoms. Markus Greiner and colleagues at Harvard University in the US studied the behaviour of lithium-6 atoms that are held in an optical lattice and interact according to rules set out by the Fermi-Hubbard model.

They found that the system becomes magnetic at low temperatures – and that the magnetism disappears when the density of atoms is reduced. The team can now use its atomic simulator to explore regimes of the Fermi-Hubbard model that could harbour very interesting physics including high-temperature superconductivity.

The electronic properties of solid materials arise from quantum-mechanical interactions between large numbers of electrons. It is notoriously difficult to calculate these properties, so physicists rely on simple models to simplify the mathematics – but even models have significant computational challenges. One such scheme is the Fermi-Hubbard model, which represents electrons as Fermi–Dirac particles (fermions) that hop between fixed sites on a lattice and only interact with each other when they occupy the same lattice site.

Physics World: Ultracold atoms shed light on the Fermi-Hubbard model
Hamish Johnston

Thursday, January 26, 2017

Flexible Ferroelectrics...

A scanning electron microscopy image of flexible haloimidazole crystals, which were found to show both ferroelectric and piezoelectric properties. (Image by Seungbum Hong/Argonne National Laboratory.)
Topics: Condensed Matter Physics, Nanotechnology, Materials Science, Metamaterials, Solid State Physics

Until recently, “flexible ferroelectrics” could have been thought of as the same type of oxymoronic phrase. However, thanks to a new discovery by the U.S. Department of Energy’s (DOE) Argonne National Laboratory in collaboration with researchers at Northwestern University, scientists have pioneered a new class of materials with advanced functionalities that moves the idea from the realm of irony into reality.

Ferroelectrics are a useful type of material that is found in capacitors that are used in sensors, as well as computer memory and RFID cards. Their special properties originate from the fact that they contain charged regions polarized in a specific orientation, which can be controlled with an external electric field. But they’ve also had a big drawback as engineers try to use them in new inventions.

“Ferroelectric materials are known for being quite brittle, and so it has always been a big challenge to make them mechanically flexible,” said Argonne nanoscientist Seungbum Hong, who helped to lead the research. “Because ferroelectricity and this kind of flexibility are relatively rare properties to see on their own, to have both ferroelectricity and flexibility in this new material is basically unprecedented.”

Argonne National Laboratory: Flexible ferroelectrics bring two material worlds together

Wednesday, October 19, 2016

Unconventional Superconductors...

A crystal sample of one of the iron-based unconventional superconductors studied by Ames Laboratory scientists. Their systematic investigation ofthis class of superconductors may lead to the creation of new materials with unique superconducting properties. Credit: U.S. Department of Energy, Ames Laboratory
Topics: Applied Physics, Condensed Matter Physics, Solid State Physics, Superconductors

Researchers at the U.S. Department of Energy's Ames Laboratory and partner institutions conducted a systematic investigation into the properties of the newest family of unconventional superconducting materials, iron-based compounds. The study may help the scientific community discover new superconducting materials with unique properties.

Researchers combined innovative crystal growth, highly sensitive magnetic measurements, and the controlled introduction of disorder through electron bombardment to create and study an entire range of compositions within a class of iron-based superconductors. They found that the key fundamental properties—transition temperature and magnetic field penetration depth—of these complex superconductors were dependent on composition and the degree of disorder in the material structure.

"This was a systematic approach to more fully understand the behavior of unconventional superconductors," said Ruslan Prozorov, Ames Laboratory faculty scientist and professor in the Department of Physics and Astronomy at Iowa State University. "We found that some proposed models of unconventional superconductivity in these iron-based compounds were compatible with our results, and this study further limited the possible theoretical mechanisms of superconductivity."Researchers combined innovative crystal growth, highly sensitive magnetic measurements, and the controlled introduction of disorder through electron bombardment to create and study an entire range of compositions within a class of iron-based superconductors. They found that the key fundamental properties—transition temperature and magnetic field penetration depth—of these complex superconductors were dependent on composition and the degree of disorder in the material structure.

Phys.org:
Scientists gain insight on mechanism of unconventional superconductivity
Ruslan Prozorov

Thursday, September 22, 2016

Electric Realpolitik...

Figure 1. A discharging battery converts chemical potential into electric potential. At the anode, an oxidation reaction frees electrons (e−) from their parent atoms. The electrons pass through an external circuit, where they do work on a load, while the ions they leave behind diffuse through an electrolyte and separator to the cathode. There, the electrons and ions recombine via a reduction reaction. During recharging, the process is reversed, and the anode is restored. In lithium-ion batteries, the electrode materials are typically layered structures, with lithium stored in the gaps between layers.
Topics: Alternative Energy, Electrical Vehicles, Green Tech, Global Warming, Solid State Physics

This post reminded me of the documentary "Who Killed the Electric Car?" and the synopsis that powerful forces - the same that fuel climate change denial as it did obfuscation on the dangers of cigarette smoking - are holding back progress because they want no other competition is the "free market" of commerce. Sounds less libertarian and more like targeted socialism for the already well-heeled 1%.

The electric vehicle’s history offers a lesson to the wise: Harvesting the fruits of basic science requires industrial foresight, investment, and a healthy dose of realpolitik.

By 2004 the all-electric vehicle seemed destined for the dustbin of history. General Motors (GM) was recalling and destroying all copies of the EV1, its first-generation electric car, after company officials convinced themselves and regulators that fuel cells, not batteries, were the ultimate power source of the future electric car. Meanwhile, hybrid electrics had begun to proliferate as a more economically viable alternative in the short run. Most batteries were then considered simply too expensive, too heavy, and too weak to power cars on their own. Then came the lithium-ion battery. (See the article by Héctor Abruña, Yasuyuki Kiya, and Jay Henderson, Physics Today, December 2008, page 43.) With higher energy density than older rechargeables—and with the ability to release that energy quickly on demand—the battery is widely viewed as having led a revival of the electric vehicle. Tesla Motors pioneered its use in automobiles with the Roadster, and today most all-electric vehicles have batteries that use some sort of lithium chemistry. Although concerns about safety, cost, and durability linger, few would dispute that the lithium-ion battery has been the chief technological enabler of the renaissance of the all-electric vehicle.

The emergence of the lithium-ion battery did not happen overnight. It was shaped for decades by the influence of materials scientists. It was the product not of a singular eureka moment but of many strands of research tracing back to the rise of the US national security state at the dawn of the Cold War. That’s when John Goodenough, a physicist by training, found himself helping to build a sophisticated air-defense computer for the US military. Although he couldn’t have imagined it at the time, he was about to embark on research that would help found solid-state ionics—the science of inserting and storing ions inside solids without changing their fundamental structures—and contribute to revolutionizing automobile transport.

The many twists and turns that ensued illustrate the unpredictability and contingency of innovation. The story of the long road to lithium-ion power shows how changing social, economic, and environmental conditions after World War II altered the R&D priorities of government and industry. It affords insight into how trends in the energy economy shaped science and engineering over time. And it reveals a hidden history of the shifting fortunes of physics, a discipline that has traditionally relied on state patronage.

Physics Today:
Cold War computers, California supercars, and the pursuit of lithium-ion power
Matthew N. Eisler

Monday, September 12, 2016

Ultracapacitors...

FastCAP Systems' ultracapacitors (pictured) can withstand extreme temperatures and harsh environments, opening up new uses for the devices across a wide range of industries, including oil and gas, aerospace and defense, and electric vehicles. Credit: FastCAP Systems
Topics: Condensed Matter Physics, Materials Science, Solid State Physics

Devices called ultracapacitors have recently become attractive forms of energy storage: They recharge in seconds, have very long lifespans, work with close to 100 percent efficiency, and are much lighter and less volatile than batteries. But they suffer from low energy-storage capacity and other drawbacks, meaning they mostly serve as backup power sources for things like electric cars, renewable energy technologies, and consumer devices.

But MIT spinout FastCAP Systems is developing ultracapacitors, and ultracapacitor-based systems, that offer greater energy density and other advancements. This technology has opened up new uses for the devices across a wide range of industries, including some that operate in extreme environments.

Based on MIT research, FastCAP's ultracapacitors store up to 10 times the energy and achieve 10 times the power density of commercial counterparts. They're also the only commercial ultracapacitors capable of withstanding temperatures reaching as high as 300 degrees Celsius and as low as minus 110 C, allowing them to endure conditions found in drilling wells and outer space. Most recently, the company developed a AA-battery-sized ultracapacitor with the perks of its bigger models, so clients can put the devices in places where ultracapacitors couldn't fit before.

Phys.org: New applications for ultracapacitors, Rob Matheson

Tuesday, September 6, 2016

Na vs Li...

Electrochemical characteristics of Na2Ti3O7 and VOPO4 electrodes in the "half-cell format" vs. Na+/Na. Courtesy: G Yu
Topics: Condensed Matter Physics, Nanotechnology, Semiconductor Technology, Solid State Physics

Researchers at the University of Texas at Austin in the US and Nanjing University of Aeronautics and Astronautics in China have developed a high-energy sodium-ion battery based on sodium titanate nanotubes and vanadyl phosphate layered nanosheet materials. The new device, which works over a wide temperature range of between –20 to +55°C, has a high operating voltage of close to 2.9 V and delivers a large reversible capacity of 114 mA h/g. It also boasts a high energy density of 220 Wh/kg, which makes it competitive with state-of-the-art lithium-ion batteries.

Sodium-ion batteries are similar to their lithium-ion cousins since they store energy in the same way. They consist of two electrodes – anode and cathode – separated by an electrolyte. When the battery is being charged with electrical energy, metal ions move from the cathode through the electrolyte to the anode, where they are absorbed into the bulk of the anode material. Sodium-based devices are in principle more attractive though since sodium is highly abundant on Earth (its Clarke’s number is 2.64) and is therefore much cheaper than lithium. Sodium is also more environmentally friendly than lithium.

However, the radius of the sodium ion is significantly larger than that of the lithium ion. This makes it difficult to find a host electrolyte material that allows ions to be rapidly absorbed and removed. What is more, sodium-ion batteries made thus far suffer from a relatively low working potential, large capacity decay during cycling (which leads to a limited battery life) and poor safety.

Nanotechweb: Sodium-ion device could compete with lithium-ion batteries, Belle Dumé

Wednesday, June 1, 2016

Reading, Writing, Magnetism...

A depiction of magnetic charge ice. Nanoscale magnets are arranged in a two-dimensional lattice. Each nanomagnet produces a pair of magnetic charges, one positive (red ball on the north pole) and one negative (blue ball on the south pole). The magnetic flux lines (white) point from positive charges to negative charges. (Image credit: Yong-Lei Wang/Zhili Xiao)

Topics: Computer Science, Condensed Matter Physics, Electromagnetism, Materials Science, Nanotechnology, Solid State Physics

Note: Title is derived from the home page (third frame in CSS - cascading style sheet format) on ANL.gov.

A team of scientists working at the U.S. Department of Energy's (DOE's) Argonne National Laboratory has created a new material, called "rewritable magnetic charge ice," that permits an unprecedented degree of control over local magnetic fields and could pave the way for new computing technologies.

The scientists' research report on development of magnetic charge ice is published in the May 20 issue of the journal Science. "With potential applications involving data storage, memory and logic devices, magnetic charge ice could someday lead to smaller and more powerful computers or even play a role in quantum computing." said Zhili Xiao who holds a joint appointment between Argonne and Northern Illinois University.

Current magnetic storage and recording devices, such as computer hard disks, contain nanomagnets with two polarities, each of which is used to represent either 0 or 1 — the binary digits, or bits, used in computers. A magnetic charge ice system could have eight possible configurations instead of two, resulting in denser storage capabilities or added functionality unavailable in current technologies.

Argonne National Laboratories:
Scientists create 'magnetic charge ice', Jared Sagoff, Tom Parisi

Tuesday, May 3, 2016

AlN and Qbits...

This graphic illustrates an engineered nitrogen vacancy in aluminum nitride.
Topics: Computer Science, Entanglement, Materials Science, Quantum Computer, Quantum Mechanics, Schrödinger’s cat, Solid State Physics

I included a short primer on Aluminum Nitride if you're interested (which, I'm guessing if you're reading something this nerdy, you kinda are). If you're viewing this on a laptop, pad or a mobile phone, I'm 99.99999999% sure your devices chips were manufactured with AlN. If you go to the link below, the article gives a succinct description of quantum entanglement (when atoms due to their proximity to each other cannot be described as a single unit), and superposition - famously illustrated by the Schrödinger’s cat thought experiment, which is the whole POINT of a quantum computer: it could be "1"; "0" or both at the same time, called a superposition of states. Thankfully, a lot of smart brains are tasked with what shape our tech lives post-Silicon will take, with which we will promptly share more cute cat videos in a kind of weird, digital Freudian slip.

Smiley

Quantum computers have the potential to break common cryptography techniques, search huge datasets and simulate quantum systems in a fraction of the time it would take today’s computers. But before this can happen, engineers need to be able to harness the properties of quantum bits or qubits.

Currently, one of the leading methods for creating qubits in materials involves exploiting the structural atomic defects in diamond. But several researchers at the University of Chicago and Argonne National Laboratory believe that if an analogue defect could be engineered into a less expensive material, the cost of manufacturing quantum technologies could be significantly reduced. Using supercomputers at the National Energy Research Scientific Computing Center (NERSC), which is located at the Lawrence Berkeley National Laboratory (Berkeley Lab), these researchers have identified a possible candidate in aluminum nitride. Their findings were published in Nature Scientific Reports.

NERSC: Could Aluminum Nitride Produce Quantum Bits? Linda Vu
Seo, H. et al. Design of defect spins in piezoelectric aluminum nitride for solid-state hybrid quantum technologies. Sci. Rep. 6, 20803; doi: 10.1038/srep20803 (2016).

Monday, March 7, 2016

III-V Semiconductor Superlattices...

FIG. 1.
Even between lattice-matched crystalline materials, there exist nonuniform transition layers that behave as an effective atomic-scale interface roughness with some rms height Δ. This effective interface roughness leads to phonon-momentum randomization and to interface resistance in cross-plane transport.
Citation: J. Appl. Phys. 118, 175101 (2015); http://dx.doi.org/10.1063/1.4935142

Topics: Applied Physics, Materials Science, Nanotechnology, Phonons, Semiconductor Technology, Solid State Physics, Thermodynamics

Abstract
This paper presents a semiclassical model for the anisotropic thermal transport in III-V semiconductor superlattices (SLs). An effective interface rms roughness is the only adjustable parameter. Thermal transport inside a layer is described by the Boltzmann transport equation in the relaxation time approximation and is affected by the relevant scattering mechanisms (three-phonon, mass-difference, and dopant and electron scattering of phonons), as well as by diffuse scattering from the interfaces captured via an effective interface scattering rate. The in-plane thermal conductivity is obtained from the layer conductivities connected in parallel. The cross-plane thermal conductivity is calculated from the layer thermal conductivities in series with one another and with thermal boundary resistances (TBRs) associated with each interface; the TBRs dominate cross-plane transport. The TBR of each interface is calculated from the transmission coefficient obtained by interpolating between the acoustic mismatch model (AMM) and the diffuse mismatch model (DMM), where the weight of the AMM transmission coefficient is the same wavelength-dependent specularity parameter related to the effective interface rms roughness that is commonly used to describe diffuse interface scattering. The model is applied to multiple III-arsenide superlattices, and the results are in very good agreement with experimental findings. The method is both simple and accurate, easy to implement, and applicable to complicated SL systems, such as the active regions of quantum cascade lasers. It is also valid for other SL material systems with high-quality interfaces and predominantly incoherent phonon transport.

Journal of Applied Physics:
Thermal conductivity of III-V semiconductor superlattices, S. Mei, I. Knezevic

Wednesday, February 24, 2016

For The Better...

Illustration: Takashi Takahashi/Tohoku University
Topics: Condensed Matter Physics, Graphene, Materials Science, Nanotechnology, Semiconductor Technology, Superconductors, Solid State Physics, Quantum Mechanics

Graphene is an amazing conductor. The transport of electrons through graphene nanoribbons has even surpassed what scientists thought were the theoretical limits for the material—so much so that electrons moving through it seem to behave almost like photons.

Graphene’s amazing properties as a conductor has inspired some researchers to explore whether the single-atom-thick sheets of carbon could also be made into superconductors. Last year, an international research team from Canada and Germany was able to demonstrate that graphene can be made to behave that way when it’s doped with lithium atoms.

Now researchers in Japan (from Tohoku University and the University of Tokyo) have developed a new method for coaxing graphene to behave as a superconductor that has some important and distinctive differences from the previous research by the Canadian and German researchers.

IEEE: Graphene's Role as a Superconductor Just Got Better, Dexter Johnson

Tuesday, November 3, 2015

Quantum Tunneling Between Nanowires...

Figure 1, see link below
Topics: Condensed Matter Physics, Nanotechnology, Semiconductor Technology, Solid State Physics, Quantum Mechanics

Abstract
We theoretically investigate the electronic transport properties of two closely spaced L-shaped semiconductor quantum wires, for different configurations of the output channel widths as well as the distance between the wires. Within the effective-mass approximation, we solve the time-dependent Schrödinger equation using the split-operator technique that allows us to calculate the transmission probability, the total probability current, the conductance, and the wave function scattering between the energy subbands. We determine the maximum distance between the quantum wires below which a relevant non-zero transmission is still found. The transmission probability and the conductance show a strong dependence on the width of the output channel for small distances between the wires.

Journal of Applied Physics: Quantum tunneling between bent semiconductor nanowires
A. A. Sousa, Andrey Chaves, T. A. S. Pereira, G. A. Farias and F. M. Peeters

Thursday, October 29, 2015

Superconducting Uproar...

Image Source: Technology Review
Topics: Condensed Matter Physics, Materials Science, Solid State Physics, Superconductivity

TECHNOLOGY REVIEW: The world of superconductivity is in uproar. Last year, Mikhail Eremets and a couple of pals from the Max Planck Institute for Chemistry in Mainz, Germany, made the extraordinary claim that they had seen hydrogen sulphide superconducting at -70 °C. That’s some 20 degrees hotter than any other material—a huge increase over the current record.

Followers of this blog will have read about this work last December, when it was first posted to the arXiv. At the time, physicists were cautious about the work. The history of superconductivity is littered with dubious claims of high-temperature activity that later turn out to be impossible to reproduce.

But in the months since then, Eremets and co have worked hard to conjure up the final pieces of conclusive evidence. A few weeks ago, their paper was finally published in the peer reviewed journal Nature, giving it the rubber stamp of respectability that mainstream physics requires. Suddenly, superconductivity is back in the headlines.

Physics arXiv:
Superconductivity above the lowest Earth temperature in pressurized sulfur hydride
Antonio Bianconi, Thomas Jarlborg

Tuesday, September 1, 2015

Squeezing Deuterium...

Figure 1. To squeeze liquid deuterium into its metallic phase, researchers discharged the 2160 capacitors of Sandia National Laboratories’ Z machine and sent a precisely shaped 1-μs current pulse that delivered 2 MJ of energy to a target at the machine’s center. The power transmission cables, as big around as small cars, are submerged in oil or deionized water, which serves as an insulator. Electrical arcs that play over the device during discharge, shown here, make for a dazzling display. (Photo by Randy Montoya/Sandia National Laboratories.)
Citation: Phys. Today 68, 9, 12 (2015); http://dx.doi.org/10.1063/PT.3.2899

Topics: Condensed Matter Physics, Electrical Engineering, Materials Science, Solid State Physics

The world’s strongest pulsed-power source takes a shot at an 80-year-old condensed-matter-physics problem.

Hydrogen is the simplest and most abundant element in the universe. But that simplicity belies its often unpredictable nature. A case in point: Unlike the alkali metals that sit below it on the periodic table, hydrogen, even in its solid phase, remains a molecular insulator down to the lowest temperatures.

In 1935 Eugene Wigner and Hillard Huntington predicted that squeezing solid hydrogen to a sufficiently high pressure could cause it to shed its molecular bonds and transform into an atomic metal. The race to find the insulator-to-metal transition in hydrogen was on, but it’s turned out to be a marathon rather than a sprint.

High-pressure experiments are notoriously difficult, and ones on hydrogen even more so. Diamond-anvil cells, the go-to equipment for static-compression experiments, are hampered by hydrogen’s tendency to penetrate into the diamond and cause cracks. Dynamic experiments using shock compression reach higher pressures, but they heat the sample to high temperatures and only access specific values of pressure and temperature that depend on the system’s initial state. Still, experimentalists have subjected hydrogen to pressures of 320 GPa using static techniques and 500 GPa using dynamic methods but have not found the metallic phase.

Physics Today: Liquid deuterium pressured into becoming metallic, Sung Chang

Monday, August 31, 2015

Graphene Superconductor...

Graphene turns into a superconductor when decorated with lithium atoms. (Courtesy: Shutterstock/Inozemtsev Konstantin)
Topics: Condensed Matter Physics, Graphene, Materials Science, Nanotechnology, Phonons, Semiconductor Technology, Superconductors, Solid State Physics, Quantum Mechanics

THIS changes the game! The application to longer life batteries is the first thought that comes to mind. Within semiconductors, we could supplement the physical limitations we're butting up to at the Moore's Law limit with a neat change in the material chemistry used to build the circuitry. A step before and enhancement of carbon nanotubes when they eventually replace them. Exciting times!

The "wonder material" graphene has another significant quality to add to its impressive list of electrical and mechanical properties: superconductivity. Physicists in Canada and Germany have shown that graphene turns into a superconductor when doped with lithium atoms – a result that could lead to a new generation of superconducting nanoscale devices.

Graphene exhibits a range of remarkable properties, thanks to its special structure – a one-atom-thick hexagonal lattice of carbon atoms. It is far stronger than steel while also flexible, and is an excellent conductor of both electricity and heat. In its pristine form, however, it is not a superconductor.

Neither is pure graphite, but in 2005 physicists showed that graphite could be made to superconduct when chemically treated, so as to create bulk materials consisting of graphene alternated with one-atom-thick layers of another element. The best performing material thus created, calcium graphite (CaC6), has a superconducting transition temperature of 11.5 K. Theorists identified the underlying mechanism for that superconductivity as electron–phonon coupling. Phonons are vibrations in a material's crystal lattice that bind electrons together into "Cooper pairs" that can travel through the lattice without resistance – one of the hallmarks of superconductivity. It was then realized that such electron–phonon coupling might occur not just in bulk graphite compounds but also by depositing atoms of a suitable element on to single layers of graphene.

Physics World: 'Decorated' graphene is a superconductor, Edwin Cartlidge

Tuesday, December 9, 2014

Unconventional Superconductors...

Top: Ripples extending down the chain of atoms breaks translational symmetry (like a checkerboard with black and white squares), which would cause extra spots in the diffraction pattern (shown as red dots in the underlying diffraction pattern). Bottom: Stretching along one direction breaks rotational symmetry but not translational symmetry (like a checkerboard with identical squares but stretched in one of the directions), causing no additional diffraction spots. The experiments proved that a new family of superconductors has the second type of electron density distribution, called a nematic. Credit: Ben Frandsen

A team of scientists from the U.S. Department of Energy's (DOE) Brookhaven National Laboratory, Columbia Engineering, Columbia Physics and Kyoto University has discovered an unusual form of electronic order in a new family of unconventional superconductors. The finding, described in the journal Nature Communications, establishes an unexpected connection between this new group of titanium-oxypnictide superconductors and the more familiar cuprates and iron-pnictides, providing scientists with a whole new family of materials from which they can gain deeper insights into the mysteries of high-temperature superconductivity.

A team of scientists from the U.S. Department of Energy's (DOE) Brookhaven National Laboratory, Columbia Engineering, Columbia Physics and Kyoto University has discovered an unusual form of electronic order in a new family of unconventional superconductors. The finding, described in the journal Nature Communications, establishes an unexpected connection between this new group of titanium-oxypnictide superconductors and the more familiar cuprates and iron-pnictides, providing scientists with a whole new family of materials from which they can gain deeper insights into the mysteries of high-temperature superconductivity.

Phys.org:
Unusual electronic state found in new class of unconventional superconductors